Home > Products > Soil Tester > UbiBot Soil Temperature & Moisture Probe (-40℃ to +85℃) 80mm probe for GS1 & SP1
UbiBot Soil Temperature & Moisture Probe (-40℃ to +85℃) 80mm probe for GS1 & SP1
  • NULL
  • NULL
  • NULL
  • NULL

UbiBot Soil Temperature & Moisture Probe (-40℃ to +85℃) 80mm probe for GS1 & SP1

Rating: 0 out of 100 - based on 0 review(s) | Write Review | Add to Compare
SG$  113.80  98.00  
Item details

Stock: Stock available

Brand: UbiBot
  Share This   Add To Facebook

Soil Temperature & Moisture Probe
(-40℃ to +85℃) with 1.9m cable
for UbiBot IoT Device GS1 & Smart Plug SP1
(Model No.: STMPGS1)

Monitoring the soil temperature and humidity with embedded RS485 interface


This probe specialises in monitoring temperature and humidity of soil. Embedded with industrial-grade chip, the probe offers accurate measurement. The stainless steel probe can be inserted into the soil for a long term without being corroded. The durable cable ensures stable data transmission.

The Audio plug is designed for the UbiBot GS1 device and Smart Plug SP1.

The measurements are transferred to the devices, displayed on the large LCD screen and synced to the platform via network. So you can access the data instantly on the screen or remotely view them via our app or web console.

The humidity readings on the app can be switched between Relative Humidity and  Absolute Humidity. You can configure the display on the web console.


  • Support switch between RH and AH
  • Electrolysis-resistant
  • Design to pairs UbiBot GS1 device and Smart Plug SP1
  • Accurate, fast data acquistion 
  • Stainless steel probe

Application Instructions

For once use only:

Insert the steel probe point vertically to the soil at your preferred depth. Hold the probe tightly in case of it shaking. Avoid touching stones or any other hard objects, because that will damage the probe. Please wait for about 20 minutes to allow the sensor to work properly.

For long time berried in soil:

Dig a hole at over 20cm-diameter on the ground or soil in your greenhouse. Insert the steel probe point in horizontal direction to the soil. Leave the probe in the soil and you can have your data remotely.

About humidity readings:

All soil probes have been calibrated in the factory. Calibration including data points is conducted by placing the probe in the air to reach the minimum of 0% and pure water to reach the maximum 100%.  For very wet soil, the reading is expected to be around 30% depends on the soil type.  Please note that when the soil is waterlogged, the reading may jump from the values of 30%-35% to 100% as it is very close to the situation of soaking the probe in the pure water.


  • Geological Survey
  • Horticulture Temperature Monitoring
  • Succulent Plant Caring
  • Green House Soil Condition Management 


  • Soil Temperature
    • Range: -40°C to +85°C (-40°F to +185°F)
    • Accuracy: ±0.5℃
  • Soil Moisture Range
    • Range: 0 ~ 100%
    • Accuracy: ±3%(0-50%); ±5%(>50%)
    • Measuring Theory: Frequency Domain (FDR)
  • Output interface: 5V RS485
  • Communication Protocol: Modbus
  • Steel Probe Length: 80mm
  • Probe Diameter: Φ3.5mm
  • Length of Cable: 1.9 meters
  • Body Material: ABS
  • Probe Material: Stainless Steel
  • Connector: 3.5mm Audio Plug
  • Power Supply Rang: DC 5V to 12V
  • Storage Condition: -40°C to +85°C (-40°F to +185°F)